Sor 1520 OEM Flow Switch Manual do Utilizador descarregar pdf

Form 454 (11.13) ©SOR Inc.

1/8

1520 Top Mounted

Flow Switch

General Instructions

Registered Quality System to ISO 9001

The SOR

1520 Flow Switch must be mounted in a vertical position (horizontal

pipe run). Electric switching is caused by the liquid flow moving the vane and

magnet into the field of a hermetically sealed reed switch capsule. Flow

switching takes place at approximately 1 ft./sec. velocity.

Two separate cavities make up the body — one for the magnetic/vane arm,

one for the switch.

Before Installing the Level Switch



Inspect the unit for any shipment damage.



Check for mechanical clearance of the vane. The vane must

move freely without binding throughout its stroke.



Use an acceptable thread compound when installing unit to

ensure a leak-free fit and to avoid thread galling.



When installed, the direction of flow should match the direction

of the arrow on the unit.

Design and

specifications are

subject to change

without notice.

For latest revision, go to

sorinc.com

Table of Contents

Installation ....................................... 2

SIL Installation Requirements ................2

Process Connection ............................2

Electrical Connection ...........................3

Special Conditions for Safe Use ..............3

Dimensions ......................................4

ATEX and IECEx Marking Details .............6

Delaration of Conformity ......................7

Troubleshooting .................................8

Replacement Parts .............................8

NOTE: If you suspect that a product is defective, contact the factory or the SOR Representative

in your area for a return authorization number (RMA). This product should only be installed by

trained and competent personnel.

1 2 3 4 5 6 7 8

Resumo do Conteúdo

Página 1 - Flow Switch

Form 454 (11.13) ©SOR Inc. 1/8 1520 Top Mounted Flow SwitchGeneral InstructionsRegistered Quality System to ISO 9001The SOR® 1520 Flow Switch must be

Página 2 - Installation

2/8Form 454 (11.13) ©SOR Inc. Integrally mounted controls should be mounted with the vessel flange or nozzle within 3° of the vertical or horizontal c

Página 3 - Electrical Connection

Form 454 (11.13) ©SOR Inc. 3/8Do not exceed catalog stated electrical ratings. Improper current input to switch will cause permanent damage to contact

Página 4 - Dimensions

Página 5 - Drawing 0390762

Form 454 (11.13) ©SOR Inc. 5/8Linear = mm/inchesDrawing 0390762With CK Accessory – ATEX and IECEx dual approved:177.87.0014.30.5655.62.1922.20.87WRENC

Página 6 - Drawing 0720554

6/8Form 454 (11.13) ©SOR Inc. ATEX and IECEx Marking DetailsFor ATEX and IECEx Certi ed ModelsStandards Assessed To ATEX Certification: EN 60079-0:

Página 7 - of Conformity

Form 454 (11.13) ©SOR Inc. 7/8Declaration of ConformityFor ATEX/IECExCerti ed Models EC Declaration of Conformity 14685 West 105th Stre

Página 8 - Troubleshooting

8/8Form 454 (11.13) ©SOR Inc. 14685 West 105th Street, Lenexa, KS 66215  913-888-2630  800-676-6794 USA  Fax 913-888-0767Registered Quality S

Modelos relacionados 1520 Electric Flow Switch

Comentários a estes Manuais

Sem comentários

Sor 1520 OEM Flow Switch Manual do Utilizador

Consulte online ou descarregue Manual do Utilizador para Sensores Sor 1520 OEM Flow Switch. SOR 1520 OEM Flow Switch User Manual Manual do Utilizador

Resumo do Conteúdo

Modelos relacionados 1520 Electric Flow Switch

Comentários a estes Manuais

Manuais e produtos relacionados com Sensores Sor 1520 OEM Flow Switch